Types of mold cleaning agents for metal

Our mold cleaning agent is suited for the use to rubber and resin manufacturing mold and aluminum die casting mold.

The cleaning agent can remove the residue, release agent, and oxide film made by vulcanization treatment fast and without damage to the mold's surface.

Moreover, cleaner shows excellent effect, and could be used for degrease cleaning of steel, and stainless.

We will show you some of our cleaning agents developed based on experience of long term research.

First, we introduce you the popular rubber mold cleaning agent【SUNECON KR-303】, and rubber mold cleaning machine(spray type) 【SUNECON KR-303H】.

［H］on the back of the product name means the product isfor cleaning machine.

Cleaning capability (including peelability) will be as follows.

KR－303（same as DA－300）

KR－6150

KR－6140（same as KR－6130）

KR-303

We receive high reputations for cleanability and years of performance of KR-303 as rubber mold cleaning agent.
Also, concentration of SUNECON KR-303could be changed depending on the amount of dirt.

Usage

Instantly removes the carbonized vulcanizing agent and paint remover on the rubber mold. Removes mild red rust as well.
※Other usage:resin mold clening(ultrasonic), removal of carbon, degrease cleaning

KR-303
Name		KR-303
How to use		(1)Over wash Over wash the mold(over 100℃) with undiluted or diluted agent. Wash away the softened dirt by water before drying out. ※Over washed agent coul be repeatedly used. Putting drain mouth and cleaning tank to restore agent is recommended. (2)Immersion washing Put undiluted or diluted agent inside the stainless tank and warm up to 70~100℃. Immerse the mold into agent. Take out the mold and wash away with water after the dirt is seperated. ※ The water will evaporate when heating. Add water to adjust the level. ※ Incase you do not have heating equipment, immersing heated mold (over 100℃) is also available. ※ Brush if necessary when over washing and immersion washing. Be aware of GHS label when using. SUNECON R-6150 come under Poisonous and Deleterious Substances Control Act. Look the SDS for more information regarding safety and related laws.
Ingredient and cautions		Be aware of GHS label when using. SUNECON R-6150 come under Poisonous and Deleterious Substances Control Act. Look the SDS for more information regarding safety and related laws. ①Wash away with water thoroughly after washing. ②Chemical fiber may react with heated mold and produce gas. Use line material to wipe. ③Do not use for aluminum and zinc to prevent dissolving.
Product type		Domestic：20Kg（can） Shipping：24Kg（UN can）

KR－6130

Cleaning agent for resin manufacturing mold. Used to remove the gas and resin dirt after manufacturing.
KR-6130 does not come under Poisonous and Deleterious Substances Control Act nor Fire Services Act, making it easy to handle.

Usage

Cleaning of resin manufacturing mold(PC resin, PVC resin)

KR－6130
Name		KR－6130
How to use		Heat immersion (Combine with shaking and use of ultrasonic waves to gain effect)
Ingredient and cautions		①Do not use on aluminum and zinc material. Alkaline dissolute them and produce hydrogen. ②Wash off with water thoroughly after cleaning. Residue may have unfavorable effect to molding. ③Air blowing after washing and coating with rust prevention agent is recommended ④Put on rubber glove and glasses for protection. ⑤Wash away with plenty of water, and consult the doctor immediately incase of the infection to your eyes and skin.
Package		18kg can

E－7200

A detergent developed for electrolytic cleaning device to clean dirt adhesion after molding, steel skim, bavkas, and smut.

Removes stains stuck to the mold up to every corner, by phisically and chemically effecting to them. The detergent does not come under Poisonous and Deleterious Substances Control Act nor Fire Services Act, which enables you to easily handle and manage.

Usage

①Cleaning of mold [Cleaning time: 10~30min each time] (PC, PBT, ABS, PP, PPS, PA, LCP, POM, Phenol resin, etc)
②Removal of mineral oil and hydrogenerated oil
③Removal of bavkus and smut

E－7200
Name		E－7200
How to use		Put into electrolytic ultrasonic cleaner.
Ingredient and cautions		①Do not use on aluminum and zinc material. Alkaline dissolute them and produce hydrogen. ②Wash off with water thoroughly after cleaning. Residue may have unfavorable effect to molding. ③Air blowing after washing and coating with rust prevention agent is recommended ※"SUNECON NR-JW" is recommended for anti-rust agent. ④Put on rubber glove and glasses for protection. ⑤Wash away with plenty of water, and consult the doctor immediately incase of the infection to your eyes and skin.
Package		・20kg can ・22kgＵＮ can ・220kgＵＮdrum

DA－300

Usage

A detergent for aluminum dye-cast. The release agent, aluminum scrap, rust could be dissoluted or removed. DA-300 is dilutable to water, making it economically friendly.

DA－300
Name		DA－300
How to use		(1)Immersion washing Immerse the mold (room temperature) into liquid solution in the tank. Aluminum on the mold will be dissoluted with foam. (2)Brushing Brush the aluminum on the mold (room temperature) Repeat brushing when adhesion amount is large. (3)Spraying Use the sprayer to spray the liquid solution. Keep the mold above 100℃ to effectively remove carbonized dirt such as release agent. The mold will dry out quickly, so spray repeatedly and check if it is removed. Be careful if the mold is hot.
Ingredient and cautions		①Alkaline in the DA-300 will dissolute aluminum.Hydrogen gas will be generated when reacing. Use local exhaust ventilation, and ventilate thoroughly in a place without any ignition source. ②Wash off with water thoroughly after cleaning. Residue may have unfavorable effect to molding.Wash away with water before the cleaning agent dry out, when the mold is hot. ③Air blowing after washing and coating with rust prevention agent is recommended ④SUNECON DA-300 come under Poisonous and Deleterious Substances Control Act.Look the MSDS for more information regarding safety and related laws.
Product type		Domestic：20Kg（can）、200Kg（drum） Shipping：25Kg（UN can）、200Kg（UN drum）

2-8-11 Higashi-Nihonbashi, Chuo-ku, Tokyo 103-0004 Japan
813-5687-1931 weekday9:00-17:00
813-5687-1933 24 hours reception
Contact Us
Product List
813-5687-1931